Knowledge Base AutoCAD
Analyzing Buildings
Get information about the requirements analysis of a building. The demand analysis includes the calculation of the heat load, the cooling load and the ventilation concept.
Heat Load
Select a calculation basis for the calculation of the heat load according to the location and requirements of your project.
Heat load Calculation According to ISSO 51 and 53(2018)
Explains the concept of heat load calculation according to the Dutch standards ISSO 51 and ISSO 53 (2018).
About General Heat Load Data
Explains the concept of general heat load data in the context of heat load calculations.
Set Ventilation System Globally
Shows step-by-step how to set up a ventilation system for your entire project.

New Features
Learn about new features in LINEAR software.
System Requirements
Learn more about the system requirements for using the LINEAR solutions.
Supported Norms and Standards
Learn which norms and standards support the LINEAR Solutions modules.
LINEAR Installation and Administration
Learn how to install, your LINEAR software, license and keep it up to date.
Getting Started
Get basic information about the structure, function and interaction of LINEAR Solutions-programs in AutoCAD and LINEAR Building.
Preparing Building
Learn how drawings are prepared by architects to create architecture for building analysis.
Analyzing Buildings
Get information about the requirements analysis of a building. The demand analysis includes the calculation of the heat load, the cooling load and the ventilation concept.
- Heat Load
  Select a calculation basis for the calculation of the heat load according to the location and requirements of your project.
  - Heat Load Calculation Based on EN 12831-1 (2017)
    Explains the concept of heat load calculation based on EN 12831-1 (2017).
  - Heat Load Calculation Based on EN 12831 (2003)
    Explains the concept of heat load calculation based on EN 12831 (2003).
  - Heat load Calculation According to ISSO 51 and 53(2018)
    Explains the concept of heat load calculation according to the Dutch standards ISSO 51 and ISSO 53 (2018).
    - About Building Detection
      Explains the building detection concept in relation to the heat load calculation.
    - About General Heat Load Data
      Explains the concept of general heat load data in the context of heat load calculations.
      - Select Calculation Base
        Shows step-by-step how to select a calculation base for your heat load.
      - Details on Climate Data for the Netherlands
        Information on the Climate data for the Netherlands section of the general heat load data.
      - Details on Building Mass
        Information about the Building mass section in the general heat load data.
      - Setting the Thermal Bridge Supplement Globally
        Shows step-by-step how to set a thermal bridge supplement for your entire project.
      - Details on Thermal Bridge Supplement
        Information about the Thermal bridge supplement section in the general heat load data.
      - Setting the Thermal Bridge Supplement Individually
        Shows step-by-step how to set the thermal bridge supplement at the component in the room.
      - Editing the Table for Thermal Bridge Supplements
        Shows step-by-step how to edit the thermal bridge supplements table.
      - Setting Minimum Temperature of the Building
        Shows step-by-step how to set the minimum temperature for the unheated condition in a building unit.
      - Configuring the Heat Transfer System Globally and at Room Level
        Shows step-by-step how to set up a heat transfer system , both project wide and room specific.
      - Details on Heat Generator Installation Type
        Information on the Heat generator installation type section in the general heat load data.
      - Details on Heat Transfer System
        Information on the Heat transfer system section in the general heat load data.
      - Details on Safety Class ISSO 51
        Information about the ISSO 51 section in the general heat load data.
      - Set Ventilation System Globally
        Shows step-by-step how to set up a ventilation system for your entire project.
      - Set Ventilation System in Ventilation Zone
        Shows step-by-step how to define the ventilation system at the ventilation zone level.
      - Details on Ventilation
        Information on the Ventilation section in the general heat load data.
      - Details on Ventilation -> Infiltration
        Information on the Ventilation -> Infiltration section of the general heat load data.
    - About Component Values
      Explains the concept of component values.
    - About the Transmission
      Explains the concept of transmission at room level, in relation to the heat load calculation.
    - About Ventilation Data
      Explains the concept Ventilation data in relation to the heat load calculation.
    - About the Intermittent Heating Operation
      Explains the concept of intermittent heating operation at room level in connection with the heat load calculation.
  - Heat Load Calculation According to SN SIA 384/2 (2020)
    Explains the concept of heat load calculation based on SN SIA 384/2 (2020).
  - Heat Load Calculation acc. To DS 418 (2020)
    Explains the concept of heat load calculation according to the danish standard DS 418.
  - Heat Load Calculation according to SP 60.13330.2016
    Explains the concept of heat load calculation based on SP 60.13330.2016.
  - Approximate Heat Load
    Explains the concept of approximate heat load calculation by means of quick entry.
- Cooling Load Short Procedure
  Learn how to calculate a cooling load for your building based on the short procedure of VDI 2078 (1996), section 6.
- Cooling Load Dynamic
  Select a method for determining the cooling load to suit the location and requirements of your project.
Dimensioning Components
Learn how to dimension radiators, convectors, panel heating and concrete core activation systems on the basis of the requirements analysis in LINEAR Building and manufacturer-specific.
Inserting Components
Learn how to insert components from the LINEAR CAD Browser into the drawing.
Drawing Networks
Learn how to draw pipe and duct networks, generate schematics, and create slots and openings.
Calculating Networks
Learn how to calculate pipe and duct networks.
Dimensioning/Label
Learn how to label section parts and components in your drawing.
Output
Get information about material compilation in LINEAR Building. You will also learn how to print or export calculation results and material lists in your CAD program.

Set Ventilation System Globally

Shows step-by-step how to set up a ventilation system for your entire project.

Before you begin

You would like to define a project wide ventilation system.

Navigate to:

Module overview ➤ Heat load ➤ Project level ➤ General heat load data

Procedure

Open the drop-down list under Ventilation and select a ventilation system.
Enter the efficiency η value (HR) for supply or exhaust air systems.
If the Specific air permeability (10 Pa) known is known, activate the option and enter the value.
If you would like to Check air volume balance, activate the option.

Results

The ventilation system for your project is selected and set.

Name	Purpose	Lifetime	Type	Provider
CookieConsent	Saves your consent to using cookies.	1 year	HTML	Website
fe_typo_user	Assigns your browser to a session on the server.	session	HTTP	Website

Name	Purpose	Lifetime	Type	Provider
_ga	Used to distinguish users.	2 years	HTML	Google
_gat	Used to throttle request rate.	1 day	HTML	Google
_gid	Used to distinguish users.	1 day	HTML	Google
_ga_QTGLMF6700	Google Analytics cookie to throttle the request rate.	2 years	HTML	Google
_gcl_au	Used by Google AdSense to experiment with advertisement efficiency.	3 months	HTML	Google
_clck	Persists the Clarity User ID and preferences, unique to that site, on the browser. This ensures that behavior in subsequent visits to the same site will be attributed to the same user ID.	1 years	HTML	Microsoft
_clsk	Connects multiple page views by a user into a single Clarity session recording.	366 day	HTML	Microsoft
_uetsid	This is a tracking cookie used by Microsoft Bing Ads. It allows us to target a user who has visited our website before.	1 day	HTML	Microsoft
_uetvid	Used to track visitors across multiple websites to present relevant advertising based on the visitor's preferences.	390 day	HTML	Microsoft
ln_or	Registers statistical data on users’ behaviour on the website. Used for internal anyalyzes by the website operator.	1 day	HTML	LinkedIn

LINEAIR VOOR AUTODESK REVIT

LINEAIR VOOR AUTODESK AUTOCAD

Set Ventilation System Globally

Before you begin

Navigate to:

Procedure

Results