Knowledge Base AutoCAD
Calculating Networks
Learn how to calculate pipe and duct networks.
About the Pipe Network Calculation for Wastewater and Roof Drainage
Explains the concept of the Pipe Network Calculation Waste Water.
Settings
Explains the concept of the Settings in the Pipe and Duct Network Calculations.
General Settings
Explains the concept for general settings in the Pipe Network Calculation Waste Water.
Specifying General Settings for Open Drainage (Wastewater)
Shows step-by-step how to set general settings for the calculation.

New Features
Learn about new features in LINEAR software.
System Requirements
Learn more about the system requirements for using the LINEAR solutions.
Supported Norms and Standards
Learn which norms and standards support the LINEAR Solutions modules.
LINEAR Installation and Administration
Learn how to install, your LINEAR software, license and keep it up to date.
Getting Started
Get basic information about the structure, function and interaction of the LINEAR Solutions programs in AutoCAD and LINEAR Building.
Preparing and Editing Buildings and Architecture
Learn how to prepare drawings provided by an architect to create an architecture for building analysis.
Analyzing Buildings
Get information about the demands analysis of a building with LINEAR Building. The demands analysis includes the calculation of the heat load, the cooling load and the determination of the required air volumes.
Dimensioning Components
Learn how radiators, convectors, panel heating/cooling systems and concrete core activation systems and components of ventilation systems are designed based on the requirement analysis in LINEAR Building.
Create Pipe Run Scheme
Learn how to create pipe run schemes for pipe networks in LINEAR Building.
Calculate Pipe Run Schemes
Learn how to calculate pipe run schemes in LINEAR Building.
Inserting Components
Learn how to transfer radiators or chilled beams to a LINEAR Building connected CAD platform and insert symbols and components from the libraries into CAD.
Drawing Networks
Learn how to draw pipe and duct networks, connect components, generate schemes, and create slots and openings.
Calculating Networks
Learn how to calculate pipe and duct networks.
- Requirements for a Calculable Pipe and Duct Network
  Explains the requirements for a calculable pipe and duct network.
- About Classification
  Explains the concept of classifying components for the Pipe and Duct Network Calculation.
- About Virtual Components
  Explains the concept of virtual components in pipe and duct network calculations.
- About Pipe Network Calculation Heating and Cooling
  Explains the concept of the pipe network calculation for heating and cooling.
- About Pipe Network Calculation Potable Water
  Explains the concept of the Pipe Network Calculation Potable Water.
- About the Pipe Network Calculation for Wastewater and Roof Drainage
  Explains the concept of the Pipe Network Calculation Waste Water.
  - Settings
    Explains the concept of the Settings in the Pipe and Duct Network Calculations.
    - General Settings
      Explains the concept for general settings in the Pipe Network Calculation Waste Water.
      - Specifying General Settings for Siphonic Drainage (Roof Drainage)
        Shows step-by-step how to set general settings for the calculation.
      - Specifying General Settings for Open Drainage (Wastewater)
        Shows step-by-step how to set general settings for the calculation.
      - Setting Layers for Network Detection
        Shows step-by-step how to select layers that should be considered in the detection.
      - Detecting a Partial Pipe Network
        Shows step-by-step how to limit the detection of components and pipes or ducts for calculation to partial networks.
      - Setting Flushing Quantities Globally
        Shows step-by-step how to set flushing quantities and sizing specifications for all WCs in the project.
      - Details on "Settings” (Waste Water/ Roof Drainage)
        Information on the Settings dialog in the Pipe Network Calculation Waste Water and Roof Drainage .
    - Material Data
      Explains the concept of material data in the pipe network calculation for Heating, Cooling and Potable water.
    - Components
      Explains the concept of the Components section in Pipe and Duct Network Calculations.
  - Calculation
    Explains the concept of the calculation dialog in Pipe and Duct Network Calculations.
  - Assign Position
    Explains the concept of localization of section parts in the pipe network calculation for Waste water.
  - Usage Units (Waste Water)
    Explains the concept op Usage units when using SP30.13330.2016 in pipe network calculation for waste water.
- About Pipe Network Calculation for Gas
  Explains the concept of the Pipe Network Calculation Gas.
- About the Air Duct Network Calculation
  Explains the concept of the Duct Network Calculation.
- About Reports (Command Group)
  Explains the concept of the Reports command group on the Analyse tab of the Control Board.
Labeling and Dimensiong
Learn how to label components and sections in your drawing and how to dimension your drawing.
Output
Get basic information on creating output with AutoCAD, output in LINEAR Building and on the print mask editor.

Specifying General Settings for Open Drainage (Wastewater)

Shows step-by-step how to set general settings for the calculation.

Before you begin

You want to make sure that all parameters are set correctly before the calculation.

Note: This task serves as a support for setting basic parameters for the calculation. Deviating from or in addition to the steps listed, further settings may be required to obtain the desired result.

Navigate to

Project tab ➤ Discipline: Waste Water ➤ Analyse Tab ➤ Settings ... ➤ Drainage

Applies to: Waste Water (Open Drainage).

General tab in the Settings for Waste Water Water in the LINEAR Solutions for Autodesk AutoCAD

Procedure

In the section Method, select the desired calculation method from the first drop-down list.
Under Buildings, select the necessary building type to set a standard-compliant discharge coefficient for the calculation.
If applicable, enable the options for ground pipes with increased filling level.
Check the values for Minimum Slope and adjust if necessary.
Click the tab Rainfall Rate and set the rainfall rate for your project site.
Close the dialog with a click on OK.

Results

The basic settings for the calculation have been defined and will be taken into account in the next calculation.

Name	Purpose	Lifetime	Type	Provider
CookieConsent	Saves your consent to using cookies.	1 year	HTML	Website
fe_typo_user	Assigns your browser to a session on the server.	session	HTTP	Website

Name	Purpose	Lifetime	Type	Provider
_ga	Used to distinguish users.	2 years	HTML	Google
_gat	Used to throttle request rate.	1 day	HTML	Google
_gid	Used to distinguish users.	1 day	HTML	Google
_ga_QTGLMF6700	Google Analytics cookie to throttle the request rate.	2 years	HTML	Google
_gcl_au	Used by Google AdSense to experiment with advertisement efficiency.	3 months	HTML	Google
_clck	Persists the Clarity User ID and preferences, unique to that site, on the browser. This ensures that behavior in subsequent visits to the same site will be attributed to the same user ID.	1 years	HTML	Microsoft
_clsk	Connects multiple page views by a user into a single Clarity session recording.	366 day	HTML	Microsoft
_uetsid	This is a tracking cookie used by Microsoft Bing Ads. It allows us to target a user who has visited our website before.	1 day	HTML	Microsoft
_uetvid	Used to track visitors across multiple websites to present relevant advertising based on the visitor's preferences.	390 day	HTML	Microsoft
ln_or	Registers statistical data on users’ behaviour on the website. Used for internal anyalyzes by the website operator.	1 day	HTML	LinkedIn

LINEAR DLA AUTODESK REVIT

LINIOWY DLA AUTODESK AUTOCAD

Specifying General Settings for Open Drainage (Wastewater)

Before you begin

Navigate to

Procedure

Results